Atdec Flat Panel Television Atdec Flat Panel Television User Manual

0

Out of 0 Ratings

Owner's of the Atdec Flat Panel Television Atdec Flat Panel Television gave it a score of 0 out of 5. Here's how the scores stacked up:

  • Reliability

    0 out of 5

  • Durability

    0 out of 5

  • Maintenance

    0 out of 5

  • Performance

    0 out of 5

  • Ease of Use

    0 out of 5
of 2
 
TIGHTEN
FIRMLY
ROTATE 90°
ROTATE
Step 3. Attaching the Articulated Arm to the Wall
Timber Stud Wall
- Using the Drilling Guide, drill three 7mm (
9
/
32
”)
diameter holes, 60mm (2
3
/
8
”) deep.
- Secure the Mouting Plate to the wall using the Coach
Screw and Washers supplied.
Masonry Wall
- Using the Drilling Guide, drill three 12mm (½”)
diameter holes, 60mm (2
3
/
8
”) deep.
- Secure the Mouting Plate to the wall using the Coach
Screw, Washers and Anchors supplied.
Remove the Telehook Arm from
the packaging and open fully.
Un-clip the Wall Plate
Cover and slide down the arm.
Wall Plate Cover
Coach Screw
M10 (x3)
Coach Bolt
M10 (x3)
Masonry
Wall
Timber
Stud
Concrete
Anchor (x3)
Step 4. Attaching the Mounting Brackets to your Display
Top of
Display
Back of Display
Choose appropriate Mounting Screws and Washers
from the Hardware supplied to suit your Display.
Mounting Screws (x4)
Washers (x4)
Mounting
Bracket
Recessed Mounting Holes or
Display with a Curved Rear Panel
Mounting
Screw
Spacer
Bush
Mounting
Hole
Washer
Step 6. Attaching the Mounting Rail to the Mounting Brackets
Slide the Mounting Rail under
both Mounting Brackets.
Centralise the Mounting Rail on
the Display, then reinstall the
Locking Plates to clamp the
Mounting Rail in position.
If the Mounting Holes are recessed
into the back of the Display, or the
Display has a curved rear panel, use
the appropriate Spacer Bushes
supplied to pack the Mounting Holes.
NOTE: Ensure the Mounting Bracket
is securely fixed to the Display.
Mounting
Hole
Coach Washer
M10 (x3)
Coach Washer
M10 (x3)
TIP: Secure the Mounting Bracket to the Display
through the top hole first, then the bottom slot.
Remove the Locking Plate from
each Mounting Bracket using the
5mm Allen Key supplied.
Locking
Plate
LOOSEN
5mm
Allen Key
Mounting
Bracket
CENTRE
Mounting
Rail
Mounting
Bracket
Locking
Plate
5mm
Allen Key
Mounting
Bracket
TIGHTEN
FIRMLY
Step 5. Landscape or Portrait Setup
NOTE: The Mounting Rail is factory set to mount the Display in a landscape position.
If you wish to mount the Display in a portrait position, please carry out the following instructions (if not, skip to Step 6).
Remove the:
• Cover Plate.
• Two Button Head Screws using the
5mm Allen Key supplied.
TIP: Use a small Flat Blade
Screwdriver to help prise the
Cover Plate loose.
LOOSEN
5mm
Allen Key
Cover
Plate
Loosen, but do not remove the
Centre Pin using the 6mm Allen Key
supplied.
Rotate the Hook Plate 90°,
then re-tighten the Centre Pin.
LOOSEN
TIGHTEN
Centre
Pin
Hook
Plate
6mm Allen Key
Remove the lower Cable Clip.
Then reinstall the two Button Head
Screws and Cover Plate.
PUSH
PUSH
Cable Clip
OR

   Find Your Products By Category