Uniden Cordless Telephone EXI8560 User Manual

5.0

Out of 2 Ratings

Owner's of the Uniden Cordless Telephone EXI8560 gave it a score of 5.0 out of 5. Here's how the scores stacked up:

  • Reliability

    5.0 out of 5

  • Durability

    5.0 out of 5

  • Maintenance

    5.0 out of 5

  • Performance

    5.0 out of 5

  • Ease of Use

    5.0 out of 5
of 12
 
Sheet 3
1-4. Connect the Telephone Cord
If you receive high-speed internet service
through your telephone line (referred to as
DSL), you should install a DSL lter between
the telephone base and the wall jack. Standard
telephones often can’t operate correctly without
a DSL lter.
Test the connection
11
Make a quick test call, and then press [END] to hang up.
What if the call doesn't go through?
Try changing the dial mode (see below).
What if there is a lot of static?
Check the sources of interference described in section
1-1 on Choosing the best location: is the base near
any of those?
Changing from tone to pulse dialing (DIAL)
Your phone can communicate with the telephone network in two dierent ways: tone dialing or pulse dialing.
These days, most phone networks use a method called tone dialing, so your phone comes programmed for tone
dialing.
If your phone company uses pulse dialing, you need to change your phone’s dial settings. If you don't get a dial
tone or can't connect to the telephone network, follow the steps below to modify your phone’s settings:
With the phone in standby, press and hold [cid/menu].
Press [ ] to move the pointer to DIAL.
Press [select/channel] to set the phone to pulse dialing.
Press [END] and put the handset back in the base. The handset communicates the new setting to the
base.
Note: If you use pulse dialing and you need to send DTMF tones during a call (if you're using an automated
response system, for example), press [ /tone/ ] to temporarily switch to tone dialing. When the call
ends, the phone automatically returns to pulse dialing mode.
Now your phone is ready to use!
1-5. Attach the Belt Clip
To attach the belt clip
Insert the tabs on the side of the belt clip into the holes on either side of the handset.
Press the belt clip down until it clicks into place. (Tug on the clip to make sure it’s
secure.)
To remove the belt clip
Gently pull the tabs out of the holes, then slide the belt clip o of the handset.
1)
2)
3)
4)
8
Connect the telephone cord to the
TEL LINE jack on the rear of the base.
9
Connect the telephone cord
to a telephone wall jack.
To telephone
wall jack
Telephone cord (supplied)
Note: If the telephone cord does not fit into your telephone wall jack, contact your
local phone provider for assistance.
To TEL LINE
8
Connect the telephone cord to the
TEL LINE jack on the rear of the base.
9
Connect the telephone cord
to a telephone wall jack.
To telephone
wall jack
Telephone cord (supplied)
Note: If the telephone cord does not fit into your telephone wall jack, contact your
local phone provider for assistance.
To TEL LINE
Telephone
wall jack
Telephone cord
DSL filter
Telephone
wall jack
Telephone cord
DSL filter
10
Pick up the handset from the base and press [TALK/flash].
You should hear a dial tone, and the display should show TALK.
What if I can't hear a dial tone?
Check the telephone cord connection on the base.
What if the display doesn't show TALK?
Put the handset back in the base for at least five seconds.
Make sure the /in use LED flashes.
Talk 0:01
10
Pick up the handset from the base and press [TALK/flash].
You should hear a dial tone, and the display should show TALK.
What if I can't hear a dial tone?
Check the telephone cord connection on the base.
What if the display doesn't show TALK?
Put the handset back in the base for at least five seconds.
Make sure the /in use LED flashes.
Talk 0:01

   Find Your Products By Category